# Changelog
FastSealCreator documented changes:

## [5.5.1.8] - 2025-07-08
- WARNING: This version brings MANY internal changes. Do not update if you are on a middle of a urgent job.
- Added oil thread machining https://www.fastseal.eu/blog/oilthread
- Template parser rewritten
- Conditional expression changed https://www.fastseal.eu/blog/templates-extra/
- Documentation on reserved words for threads added in: https://www.fastseal.eu/blog/reserved-words-templates/#thread
- Improvements on several profiles

## [5.5.1.7] - 2025-07-06
- Internal tester version, not released

## [5.5.1.6] - 2025-07-01
- Internal tester version, not released

## [5.5.1.5] - 2025-06-17
- Added extended machining length to control a extra amount of Z machining length based on each tool
- Added PS21E; PS18U, V and W
- Print documents with oring and/or spring if profile contains those elements
- Custom datasheet location for tooling https://www.fastseal.eu/blog/custom-tool-datasheet/

## [5.5.1.4] - 2025-06-10
- Improvement on import gcode based on customers feedback
- Improvement on program start (avoiding multiple accidental starts *testing*)

## [5.5.1.3] - 2025-06-06
- Added RS18U, V and W
- Added overlap of grooves that ends with a vertical geometry
- Minor changes and corrections

## [5.5.1.2] - 2025-06-04
- Added R20K, PS63P, PS63R
- Correction on spring grooves affected by one single pass (reverted for springs change on update 5.5.0.9)
- Improvents on several profiles
- Better parse on gcode with I K values for arcs
- Improvements on gcode import (forcing user to add a valid profile name and nominals)

## [5.5.1.1] - 2025-05-25
- Added PS16PG, PS18S, GR12
- Corrections on SES01, SES02, RS23B
- Correction on tool table where the program could crash

## [5.5.1.0] - 2025-05-22
- Added part off method to cut from inside to outside when tool tip direction is set to 1, 2 or 6 https://www.fastseal.eu/blog/part-off-from-inside-to-outside/
- Print folder was not being saved correctly when switching between machines
- Introduction of import gcode file from serial port (beta)
- Introduction of import gcode file and use it as a standard workitem (file or serial port) (beta)
- Corrections on several profiles
- Machining part options on the machine settings separated by cycles

## [5.5.0.9] - 2025-05-19
- Front grooves depth passes are made taking in consideration the tool reach (before always 2 passes)
- OR machining with just one oring cutting pass if cross section is lower than 10mm
- PS16 and RS16 series with forced lower machining path (0.1mm) on the sealing zone
- Templates can have unicode characters https://www.fastseal.eu/blog/templates-extra/
- Corrected country names with () on Fanuc machines (nested comments)
- Templates can have IF THEN ELSE conditions, set with ::: https://www.fastseal.eu/blog/templates-extra/
- Added the possibility for metal/seal dimensions on VPA01 individual units series
- New reserved word for {Profile.HasOverlimit} https://www.fastseal.eu/blog/reserved-words-templates/
- Debug information on part numbers load if price or revision could not be set as numeric value

## [5.5.0.8] - 2025-04-24
- License minor changes
- Download page on software with correct changelog
- Small profiles improvements

## [5.5.0.7] - 2025-04-22
- Customer company name for WebFastQuote uniformized
- Minor changes

## [5.5.0.6] - 2025-04-17
- Correction on sorting the compounds table
- Minor corrections on several profiles
- Added ST10, ST11, ST12, ST13

## [5.5.0.5] - 2025-04-16
- Activation using https://portal.fastseal.eu

## [5.5.0.4] - 2025-04-15
- Tester version for updater
- Minor improvements

## [5.5.0.3] - 2025-04-14
- Release of the fastseal portal: https://portal.fastseal.eu
- More information in: https://www.fastseal.eu/blog/portal
- Implementation of new activation method

## [5.5.0.2] - 2025-04-11
- WARNING - Final release before fastseal portal is online. New activation method will be needed.
- More information in: https://www.fastseal.eu/blog/portal and https://www.fastseal.eu/blog/online-activation
- ****
- Minor change on RS07A and PS18O
- Corrected rough machining on specific cases where the rough path matches the final shape several times on its edges

## [5.5.0.1] - 2025-04-09
- Introduction of new machining method for angle grooves (https://www.fastseal.eu/blog/oring-tools-grooves-with-angles)
- Correction on part numbers with complex shapes that generated large images that were rejected by the database
- Wiper facing finish with outside tool

## [5.5.0.0] - 2025-04-01
- Added BU05B, RS05Q
- Added control for length of inside lip on RS10P and R
- Preparing for major release with online customer portal for licensing management

## [5.4.9.9] - 2025-03-21
- Less limits on R11A, B and C
- Better dimension display after a drawing is displayed as impossible
- Added chamfers angles control on SS22
- Reserved words related with material and profiles dimensions affected by the machine option to remove insignificant zeros

## [5.4.9.8] - 2025-03-19
- Added Tool.Step to reserved words for drilling tools (normally used on live tooling)
- Added ORJ2
- Corrected bug on price per unit on FastQuote system
- Internal preparations to use the FastSeal portal so that licenses and updates can be managed by the client
- Crash correction when template has a wrong number of pipe '|' characters
- Improved user control on WF01A, B and C

## [5.4.9.7] - 2025-03-16
- Added ID column on compounds table
- Added the possibility of hiding/showing columns on compounds table (mouse-right click)
- Changed behaviour: A quote that moves to work is set a pending by default
- WebFastQuote: Added price depending on quantity (before only total quantity was displayed)

## [5.4.9.6] - 2025-03-14
- Fixed crash when material information on print documents user setting was empty (https://www.fastseal.eu/blog/machine-settings-templates/)
- Improved WF02 series oring manipulation

## [5.4.9.5] - 2025-03-13
- Templates for material information on seal print and work print (see https://www.fastseal.eu/blog/machine-settings-templates/)
- Important correction on date and time representation on different countries (download limit date was not being displayed)
- Important correction on database to store last used material
- Minor changes on profiles nominal limits
- Added PS19C, BUP13

## [5.4.9.4] - 2025-03-12
- Internal test release

## [5.4.9.3] - 2025-03-07
- Improvements on crash protection on unusual set up
- Changes on WH03D, SS18D (small dimensions now possible)

## [5.4.9.2] - 2025-02-28
- Improved groove dimensions in R10 and R11 series
- PDF Print with individual components selected material information
- Added ISM03
- Fixed crash when no tool is available for groove and a finish allowance was set

## [5.4.9.1] - 2025-02-26
- Added PDT03, WH07F
- Possible fix for DXF imports placed on folders
- Improvements on RS18K, PS18K, PS17G
- Crash protection on specific situations reported by users

## [5.4.9.0] - 2025-02-11
- Improved bounding box calculation (error verification)
- Possible improvement on storing the latest materials used (automatic)
- Added PDT02, WF02E
- Added lastuse to database backup

## [5.4.8.9] - 2025-02-06
- Material selection is saved once the gcode screen is selected *testing*
- Correction on facing up to center of material (when drilling exists)
- WH20A with new machining method *for testing*
- RS18K and PS18K improved
- Several minnor improvements on several profiles

## [5.4.8.8] - 2025-02-01
- Added ISM01, ISM02, W28
- Minor improvements

## [5.4.8.7] - 2025-01-23
- Renamed PS45 to PS45A
- Added PS45B
- Minor changes

## [5.4.8.6] - 2025-01-16
- Lower restrictions on RS15 and PS15 series
- Incompatibility with Turkish culture test fix

## [5.4.8.5] - 2025-01-13
- Change on how the smaller diameters are handle for inside and facing machining (needs extra verification)
- Added S34 and S35 based on RS16 and PS16 variantes for static applications on static group
- Redone RS16 and PS16 on the corresponding rod and piston seals so that they can be used on dynamic applications
- Possibility to select out of stock materials on sugested materials list
- Added PDT01
- More translations on machine settings
- Minor improvements

## [5.4.8.4] - 2025-01-03
- Spring calculation for RS22S, S11, S12, S24, S25

## [5.4.8.3] - 2024-12-30
- Added PS16PL
- Auto fill of spring database if empty

## [5.4.8.2] - 2024-12-23
- Added R20AL, R38, RS19K
- Springs calculation added for all piston and symmetric seals
- Improved design for R09G and R10G to comply with standard oring selection and groove quantity
- Fixed DXF import facing when no facing geometry was obtained (potentially fixed several simillar cases)

## [5.4.8.1] - 2024-12-17
- All rotary seals with new spring calculation method
- Possible fix for wrong load of database values due to culture related issues

## [5.4.8.0] - 2024-12-16
- Added springs database to automatic backup
- Second lip of RS07AD and RS07AW redesigned

## [5.4.7.9] - 2024-12-12
- WH03A, WH03B, R10 series with lower restrictions
- VPA01 series with radius 0.4 on front groove for small sizes
- Added WH18, PS45

## [5.4.7.8] - 2024-12-09
- Added FPES02L, WH12F
- Rotary seals front groove, max z reach of tools taken in consideration

## [5.4.7.7] - 2024-12-05
- Added WH18CC, PS09PH, PS10PH, PS18R, PS18Q, BUS02D
- Improvement on BUS02 series icons
- Improvement on autopath error detection
- Small improvements on several profiles

## [5.4.7.6] - 2024-12-04
- Minor changes on several profiles to improve range
- Second attempt to fix comma dot issue on spring database for some users

## [5.4.7.5] - 2024-12-02
- WF04A oring selection based on original simrit design
- Spring calculation added to R20A, R20B, R20C, R20D, R20E, R20F, R20G
- Added WF02D, PS53B
- Serial port settings operation time out forced to be >= 0
- Spring dimensions uniformized to use dot(.) instead of comma(,)
- Larger CS possible for RS05BW
- Limited backup ring groove depth to 13mm so that most of the designs are compatible with standard tools
- Other profiles with improvements/corrections

## [5.4.7.4] - 2024-11-15
- Improved spring information box
- Added new spring calculation for R01, R02, R03 and R04 series
- Minor improvements on other profiles

## [5.4.7.3] - 2024-11-15
- Added RS10B
- Added Springs database * TESTING *
- https://www.fastseal.eu/blog/springs
- Applied in R18 series, PS06S and PS22A - includes better design
 
## [5.4.7.2] - 2024-11-12
- Added option for facing cycles to select the facing tool also based on radius
- https://www.fastseal.eu/blog/machine-settings-machining/
- Added column with date information on part numbers (kit databases)
- Minor corrections and improvements on profiles

## [5.4.7.1] - 2024-11-05
- Added SS13BO, SOL03, SS24B, renamed SS24 to SS24A
- Added the possibility to machine chevrons inside with outside tool
- https://www.fastseal.eu/blog/chevron-inside-with-outside-tool/

## [5.4.7.0] - 2024-10-30
- Added WH08K, WH02C, SS06PM, PS52 series
- Corrected partoff tools with "always off" vacuum
- Corrected not available facing tool fallback
- Minor profiles improvements

## [5.4.6.9] - 2024-10-11
- Added PS51
- Minor improvement on RS22A
- Preparatory work for spring database

## [5.4.6.8] - 2024-10-02
- Optional remove of XZ instructions on GCode to reduce file size (very experimental)
- https://www.fastseal.eu/blog/machine-settings-file-structure/

## [5.4.6.7] - 2024-09-30
- Added WH03C, WH03D, WH10C, RB09, RB10
- Corrected inverted X axis to allow movements to positive values
- Attempt to fix partnumbers table initialization

## [5.4.6.6] - 2024-09-27F
- Corrected angle in WH05A and B
- Added debug information for part numbers
- Internal correction of groove tool depth verification
- Correction on latest update profile database

## [5.4.6.5] - 2024-09-25
- Added WH04C, WH07E, R20G, BUS01A
- Full control on the groove front of WH02A and B
- Restrictions also taken in consideration on facing using groove tools
- Avoid materials sync on WebFastQuote when local machine does not have materials

## [5.4.6.4] - 2024-09-20
- Added WH30, WH18F, RB08
- Code improvement for S11, S12, PS15RB, R18 and R19 series
- WH02A and B with recess made as a groove
- Reverted change on 5.4.6.3 regarding radius with 4 decimals as several controllers were unable to process it
- Reduced number of feedrate set on "universal cycle" (ex rotary seal front groove)

## [5.4.6.3] - 2024-09-13
- G04 instruction only with decimal point if the value is not integer
- Improvement on auto inside/outside code when the profile starts with an arc
- Radius with 4 decimals for increased precision
- Improved German translation
- Improved lead in on several PTFE wiper seals
- Correction on outside chamfer on several wipers (unnoticeable on several cases)
- Improved part numbers MySQL table (only affects new installations)

## [5.4.6.2] - 2024-09-03
- Several options added to reduce gcode file size:
- https://www.fastseal.eu/blog/machine-settings-file-structure/
- Tool restriction added based on material cross section
- https://www.fastseal.eu/blog/restrictions-max-cross-section/
- Possbile to add initial and end characters for serial transmission (see advanced settings)
- https://www.fastseal.eu/blog/serial-port/
- Fixed bug on radial drilling where the user could input a negative depth on the operation

## [5.4.6.1] - 2024-08-30
- Spindle speed limited on constant spindle speed to the machine spindle speed setting

## [5.4.6.0] - 2024-08-22
- Small icons added to control what component profile is to be edited
- WebFastQuote client name updated

## [5.4.5.9] - 2024-08-20
- Added S32
- Added control for oring on WH08E

## [5.4.5.8] - 2024-08-19
- Added WH08E
- Minor fix on metal profiles
- Correction when adding part numbers on imported profiles (was not supported)

## [5.4.5.7] - 2024-07-12
- Added control over groove length on S30
- Added S31

## [5.4.5.6] - 2024-07-09
- Bug fixed on manual tool change for operations without pre selected tool

## [5.4.5.5] - 2024-07-08
- Added BUR10, BUP12
- Minor improvements

## [5.4.5.4] - 2024-07-02
- Added S30
- Minor improvements

## [5.4.5.3] - 2024-06-28
- Added S28, S29, PS22F, PS22G, SS36
- Minor improvements

## [5.4.5.2] - 2024-06-10
- Material sugestions query improved over brands
- BOG03 part off corrected

## [5.4.5.1] - 2024-05-21
- Important fix on facing beyond X=0 (bug introduced on last release)
- Added RS02PR
- Attempt to correct pending works with deleted items (needs client test)

## [5.4.5.0] - 2024-05-17
- Added brand, model and controller information to the machine settings
- https://www.fastseal.eu/blog/machine-settings-identification/
- New interface for managing the machine settings
- Added R35R
- Facing on solid goes beyond X=0

## [5.4.4.9] - 2024-05-10
- Introduction of radial z cut (live tooling) see: https://www.fastseal.eu/blog/live-tooling-radial-z-cut/
- Minor improvement on FPES07B
- Correction tool settings when updating a minimum diameter machine value to a already existing tool

## [5.4.4.8] - 2024-05-06
- Internet check for Chinese locations (to avoid google block)
- Avoid program crash on simulation when no cycle is present
- Minor correction on guide ring for IC1 variable

## [5.4.4.7] - 2024-04-22
- Corrections for live tooling. Documentation also available in:
- https://www.fastseal.eu/blog/machine-settings-live-tooling/
- https://www.fastseal.eu/blog/live-tooling-reserved-words/
- Added PS22E, improvement on SS22E

## [5.4.4.6] - 2024-04-18
- Added split cut radial live tooling operation
- Improved and normalized others live tooling operations
- Added examples to the default machine for live tooling operations
- Minor errors corrected

## [5.4.4.5] - 2024-04-10
- WebFastQuote company names improved
- Corrected GR11
- Improved radial slotting (live tooling) interface

## [5.4.4.4] - 2024-04-08
- DXF import and export library update (version 0.7.5)

## [5.4.4.3] - 2024-04-08
- Control view and added operation corrected (program crash)

## [5.4.4.2] - 2024-04-08
- Load saved profiles on database corrected for live tooling operations

## [5.4.4.1] - 2024-04-08
- FastWebQuote improved
- Visual settings fully translated

## [5.4.4.0] - 2024-04-06
- FastWebQuote now available
- Added SS35, PS40C
- Leadout corrected, several minor improvements

## [5.4.3.9] - 2024-04-04
- WARNING! Extra care on toolpath should be taken into account
- Experimental removal of all unnecessary movements in inside/outside machining
- https://www.fastseal.eu/blog/ghosting-movements-removed/
- Added option to restrict the drill tool selection by maximum inside diameter
- Pre release of webfastquote
- Corrected minor issue when adding a new drilling tool
- Improvement in many seals. All seals up to 3000mm design capability
- User interaction improved, many profiles with extra dimensional checking
- Added BU08, S27
- Possible to use R=0 in inside and outside tools (experimental, for manual set of G41 and G42)

## [5.4.3.8] - 2024-03-08
- Fixed issue with extreme cross section on PS15R
- Renamed S24 to S26 (duplicated)
- Fixed issue with wrong imported values of materials

## [5.4.3.7] - 2024-03-01
- Added GR01R, S13R
- Fixed important bug (rare) related with toolpath - update recommended
- Improved database upgrade related with imported profiles
- Improved autoarc indexes (better user experience for dimensions)
- Minor bugs addressed

## [5.4.3.6] - 2024-02-20
- Added NM01, WH28A, WH29A, S24, SS34A
- Removed warning for unsuitable machining with oring tools the inside and outside cycles
- Minor fix to prevent crash when raw material dimensions are wrong added into database

## [5.4.3.5] - 2024-02-09
- Minor update on VPA03A-3S
- Increased limitation on heigh for profile RS33A
- Disable the possibility of part off tool on BUS07
- Corrected Dmin error on older tool databases the prevented adding new tools

## [5.4.3.4] - 2024-01-31
- Fixed autopath issue on very rare situation
- Improved RS18O and PS18O when manual oring cross section is made
- Fix on thread (metal) that was broken due to update [5.4.3.1]

## [5.4.3.3] - 2024-01-23
- Added SS21B, renamed SS21 to SS21A

## [5.4.3.2] - 2024-01-22
- Added PS19B
- Minor improvements on several profiles
- Stability fixes

## [5.4.3.1] - 2023-12-22
- Added new reserved word (Tool.FeedMode) that explicity sets the feed/minute or feed/revolution. Normally to be used on the tool change template.
- Changed outside front chamfers on profiles RS04P, RS05P, RS05PW, RS05R, RS06P, RS06PW, RS07A, RS07AD, RS07AW, RS07B, SS06P, SS06PIP
- Added SS33A

## [5.4.3.0] - 2023-12-13
- Added R10H, ASE01, RS18H
- Improvement on WF02 series
- Corrected X part off calculation on several GR03 when inside angle is changed

## [5.4.2.9] - 2023-12-06
- Added GR11, ORJ
- Guide rings icons uniformized
- Minor changes to improve usability

## [5.4.2.8] - 2023-11-23
- Added RS18G
- Changed name of RS16C to RS39A
- Added more orings CS to the oring selection list (1.2, 4.5 and 8.0mm)
- Fixed crash when no tools were set to axis slotting and user selected this operation
- Web fast quote developments. Documentation being created:
- https://www.fastseal.eu/blog/webfastquote-what-is-it/

## [5.4.2.7] - 2023-11-10
- Added WH07A
- Minor improvement in the tool choice (affects oring tools)
- Web fast quote developments. Documentation being created:
- https://www.fastseal.eu/blog/webfastquote-what-is-it/

## [5.4.2.6] - 2023-11-08
- Hot fix for price calculation

## [5.4.2.5] - 2023-11-08
- Downloads page with hyperlinks
- Correction for new client during the new work dialog with low user permissions
- Web fast quote developments. Documentation being created:
- https://www.fastseal.eu/blog/webfastquote-what-is-it/
- Improvement on the pre, post and after tool change specific codes:
- https://www.fastseal.eu/blog/machine-settings-templates/
- Added Set spindle speed expression:
- https://www.fastseal.eu/blog/machine-settings-spindle/
- Added WP08C

## [5.4.2.4] - 2023-11-01
- Added RS18R
- Web fast quote developments. Documentation being created. Read first:
- https://www.fastseal.eu/blog/webfastquote-what-is-it/

## [5.4.2.3] - 2023-10-28
- Hot fix due to "finish speed not set" error

## [5.4.2.2] - 2023-10-28
- Improvement on gcode generator for fixed tool RPMs
- New tool management material parameters. Also documented here:
- https://www.fastseal.eu/blog/tool-management-material-parameters/
- Internal preparation for online store ongoing *not visible*

## [5.4.2.1] - 2023-10-18
- Very important change on inside tools, user must check tool settings (https://www.fastseal.eu/blog/tool-management-cutting-limits/)

## [5.4.2.0] - 2023-10-16
- Added WH27A, WI02B, WI02C, BUS07 (https://www.fastseal.eu/blog/BUS07)
- Improved limitation to wrong geometries where the screen would not present the profile

## [5.4.1.9] - 2023-09-28
- Tool management visual aspect is being redone

## [5.4.1.8] - 2023-09-26
- Warning - several changes on tool database - may need verification
- Added radial slotting and axial slotting (live tooling)
- Added 'diameter' as the correct way to determine a size of a drill or mill (previous was radius)
- Added more geometry possibilities for each tool, specially focused on drills and mills
- Added correct geometry representation of drills and mills
- Improvements on several profiles
- Added images and default tools for all radial and milling operations on the default machine
- Added FPES16

## [5.4.1.7] - 2023-09-15
- Changes for live tooling improved compatibility (no need to update if live tooling is not used)
- More control on VPA02A
- Created VPA03B

## [5.4.1.6] - 2023-09-08
- Internal preparation for online store *not visible*
- Several bugs corrected to prevent unwanted crashes
- Added profiles: PS62, BUP11, RS19T, W20B, RS10E

## [5.4.1.5] - 2023-08-21
- Open of previous saved seals with more than one component bug fixes
- Minor changes

## [5.4.1.4] - 2023-07-17
- Added kits functionality (testing needed)
- Corrected several profiles and added clients suggestions
- Added R37A

## [5.4.1.3] - 2023-06-15
- Added reports with compounds use
- https://www.fastseal.eu/blog/reports-compounds-use-quantity/
- Corrected part off on auto path
- Added RS22G, RS22F, RS02PH

## [5.4.1.2] - 2023-06-12
- Load previous made parts with better integration
- Square preload ring fix on variables location

## [5.4.1.1] - 2023-06-10
- Added SS22R
- Minor change in WH21
- User with permission 0 cannot access client fiscal information

## [5.4.1.0] - 2023-06-07
- Minor fixes that prevented some issues
- Added reset of all profiles names to the original names on database maintenance
- Work almost completed for fastquote online
- Added SS32

## [5.4.0.9] - 2023-06-01
- Redesigned new work window for faster creation of new client
- https://www.fastseal.eu/blog/new-work-window/
- Software unhandle exceptions prevention on user reported situations 

## [5.4.0.8] - 2023-05-29
- Added: PS05B
- Improvement on dimensions of RS05B, BP
- Simulation is not preformed on cycles that are not visible
- Chinese language available

## [5.4.0.7] - 2023-05-17
- Added: WH13C, RS09AW, WG01
- Improved RS09 series

## [5.4.0.6] - 2023-05-08
- Several profiles with fixed FastQuote calculations
- Hidden profile functionality with better performance

## [5.4.0.5] - 2023-05-06
- Added standard dimensions for PS16 series
- Corrected starting crashes when remote database was not available
- Internal improvements related with Import DXF

## [5.4.0.4] - 2023-04-28
- Added PS61A
- Minor corrections related with Import DXF

## [5.4.0.3] - 2023-04-25
- IMPORTANT - This is a major release. Please backup database before updating !
- Fixed release issue with DXF reader

## [5.4.0.2] - 2023-04-21
- Fixed dropdown nominals
- Search is now made on the children folders of the current location
- Larger icons with content quantity information
- Many other small improvements on user interface
- Internal version only - not released

## [5.3.2.2] - 2023-04-21
- Front groove, lower limit can now be set to 0.4mm: https://www.fastseal.eu/blog/lower-limit-front-groove/
- Added PS26W (waiting for client approval)

## [5.3.2.1] - 2023-04-19
- Added the option to skip roughing on facing: https://www.fastseal.eu/blog/ignore-facing-roughing/
- Fix on crash when more than 5 profiles were open (on non English language PC's)
- Added increased ability on small cross section seals, SS06 series

## [5.3.2.0] - 2023-03-21
- Stock management added (experimental)

## [5.3.1.6] - 2023-03-13
- Several unhandled exceptions corrections to avoid program crashes

## [5.3.1.5] - 2023-03-05
- Added PS50, fixed several minor issues

## [5.3.1.4] - 2023-03-01
- Users with permissions=0 with more restrictions on the software use
- SS27 and SS27B can now be made with 3mm cross section

## [5.3.1.3] - 2023-02-27
- Added SS27B, RS10A
- Crash prevent on serial communication error due to removal of USB->Serial device

## [5.3.1.2] - 2023-02-26
- Added BUS04A, S24, S25
- Improvement on percentage dimensions
- Database status information corrected for user without permission

## [5.3.1.1] - 2023-02-18
- Minor fix on FPES01
- Preventive fix on program crash when no suitable tool available for facing

## [5.3.1.0] - 2023-02-13
- Error on VPA01 fixed (introduced on last release)
- Added ST02 and S23

## [5.3.0.9] - 2023-02-02
- Font size on the code window can now be changed on the visual settings
- Corrected issue on front grooves where convex radius were taking in account to choose the tool
- Import CSV now should also be able to update materials, instead of
  ignoring already existing materials using the replace option
- Most of the machine configuration is now changed and have online documentation directly accessed from the software
- Added VPA06, VPA06-2S and VPA05-3S (also enable ANG variable change)
- Improved facing finish on wipers so that the tool radius does not reach the lip
- Allow higher range on the OR CS of profile group SS06
- Option to move first the X then the Z axis https://www.fastseal.eu/blog/approximation-movement
- Added the option to all tools for inverted X axis https://www.fastseal.eu/blog/inverted-x
- Minor change on RS22D profile (added HI1 variable)
- Added information about machining over the limit https://www.fastseal.eu/blog/approximation-movement

## [5.3.0.8] - 2023-01-12
- Some errors fixed for very strange machine configurations

## [5.3.0.7] - 2023-01-04
- Fixed error introduced on last update (finishing outside elastomer was not present after polymers tools used)

## [5.3.0.6] - 2023-01-03
- Fixed error related with load of profiles with the exact name of the folder that contains them
- Fixed error on outside machining with AutoPath and polymers tools (affects ImportDXF)

## [5.3.0.5] - 2022-12-12
- Added FPES15
- Minor issue that prevented customer reports to be sent with the built in "send report"

## [5.3.0.4] - 2022-12-06
- Added FPES14, RS22E, SS31 (rod and symmetric)
- Fix error on poly rough machining z clearance
- Background work on Import DXF functionality (+- 8% completed)

## [5.3.0.3] - 2022-11-18
- Added BOG03
- Background work on Import DXF functionality (+- 7% completed)

## [5.3.0.2] - 2022-11-18
- Added BU07, FPE07B
- Minor change on FPE07
- Background work started to merge with Import DXF functionality (5% completed)

## [5.3.0.1] - 2022-11-10
- Added VPA05
- Fixed 'show all' profiles on latest version

## [5.3.0.0] - 2022-11-10
- Added PS15PB/RB; BOG02
- Change on S22 to allow control over inside groove
- Minor changes to provide robustness on uncommon situations
- Started work to prepare merge with DXF import

## [5.2.9.9] - 2022-11-03
- Added S22 and FPES13
- Limit tool image icon size to 100mm height
- Fixed database column geometry to TEXT instead of INT on older machines

## [5.2.9.8] - 2022-10-23
- Added BA01

## [5.2.9.7] - 2022-10-19
- Fixed radius compensation uncommon issue (SS10P)
- Dimension change between inches and mm is now better implemented and tolerances are also present in inches
- Minor fix on RS51 inside machining
- Added R36R

## [5.2.9.6] - 2022-10-14
- Added SS10P (codes needs extra verification - not for production, but in conditions to be tested)
- All profiles now have FastQuote information and can be used on the fastquote system
- Higher limits on R07, 08 series (able to 32.5mm cross section)

## [5.2.9.5] - 2022-10-12
- Added BOG01, R20D, R20E, R20F, SS28C
- Fixed spindle graph issue when changing machines
- Added improved machine method for facing grooving on complex grooves
- Other minor improvements on several profiles

## [5.2.9.4] - 2022-10-04
- Added R20C

## [5.2.9.3] - 2022-09-21
- Fixed internal parse error on zero point calculation (machine configuration dependable)
- Visual bug fixed on simulation where manual changed code was not displayed
- Fixed crash on simulation if the tool in use did not had a previous set feedrate (wrong settings on tool)
- Added BRU09 and RS26B
- Ongoing FastQuote information on individual profiles (about 70% completed)

## [5.2.9.2] - 2022-09-19
- Ongoing FastQuote information on individual profiles (about 65% completed)
- Fixed error on new installations where one of mysql tables was not being created
- Added RS42
- Fix search for profile that was not finding profiles with lowercase text

## [5.2.9.1] - 2022-09-13
- Ongoing FastQuote information on individual profiles (about 30% completed)
- Angle variables are now not converted to "inches"
- When the host PC add a undefined browser the program was crashing. Apparently solved.
- Minor visual improvements (text size - again!)

## [5.2.9.0] - 2022-09-09
- Piston seals with FastQuote information (still to be added on remaining profiles)
- Added WH18D, WH18E
- Added option on database settings to set the refresh rate of MySQL
- Corrupted XML setting will not crash the software, will be ignored

## [5.2.8.9] - 2022-09-01
- Added SS30, RS16F and PS16F. Moved RS16G and PS16G into the same folder as the F versions.

## [5.2.8.8] - 2022-08-30
- Simple method for removing and adding cycles in gcode https://www.fastseal.eu/blog/removing-and-adding-cycles-in-gcode/
- Minor changes on PS16G and PS18O. Fixed bug on statistics if client name was wrong the the database.
- Update on non standard dimensions for profiles PS17 series

## [5.2.8.7] - 2022-08-19
- Added tools 54 and 55 to default machine, https://www.fastseal.eu/blog/new-tools-53-54-and-55/
- Added SOL2, R34
- Improved dimensions size on very large profiles

## [5.2.8.6] - 2022-08-15
- Added tool 53 to default machine, I503 https://store.fastseal.eu/index.php?route=product/product&path=59_66_79&product_id=244
- Designers team changed software main icon changed *again*
- Fixed duplicated destination gcode line *very rare issue*. Hopefully does not affect correct toolpaths.
- FastQuote with help page https://www.fastseal.eu/blog/fastquote/
- Added missing icons on non standard nominals (I2, I3, ...)
- Added SES06
- Limited this change log for the last year

## [5.2.8.5] - 2022-08-11
- CSV importer now has invariant culture (avoids reading numbers incorrectly)
- Fixed importer issue related with already exisiting brand
- Improved seal material edit window that was cropping text on several languages
- Added Stock as a built in filter on the compounds database
- Added SOL01
- Added missing software icon

## [5.2.8.4] - 2022-08-10
- Small correction on simulation to avoid reported crash
- Icons change to FastSeal logo
- Added complexity factor on the fastquote (documentation to follow)
- Improved compounds menu (organization)

## [5.2.8.3] - 2022-08-08
- Improved import of CSV files. Check https://www.fastseal.eu/blog/import-compounds/
- Faster load of database compounds database menu
- Built in filters on materials present on database compounds
- Minor improvements

## [5.2.8.2] - 2022-08-07
- ** WARNING **
- New database materials querys to optimize large number of results. Affects material selection (tab 2 when producing a profile) and fastquote
- ** Please report wrong results **
-
- New profiles: SS13NR, RS07D, RS22C, RS22D
- Minor changes on PS15PL, PS15RL, RS15PL, RS15RL and SS24 to comply to client request

## [5.2.8.1] - 2022-07-28
- Bug fixed on filter radio box selection 
- Removed some seals nominals limitations due to user request
- Fixed small bugs introduced on update 5.2.8.0
- Improved work database load time
- Improved material selection on FastQuote
- Target framework is now .NET 4.7.2 (end client needs to update or download Microsoft packages?)
- FastSeal store link on tool database
- High resolution profiles images are now generated automatically - to supply on request

## [5.2.8.0] - 2022-07-22
- Added FastQuote functionality
- Simulation reworked
- Added translation to several menus (most related with prices)
- Added tool restriction to more groups
- Minor features added and bugs corrected
- Improved tool tree view menu with icons
- Several small bugs with profiles corrected
- Added database maintenance tools on settings
- Added improved work and quotes filter (quantity)

## [5.2.7.0] - 2022-06-21
- Changed print dialog window style to test compatibility on Windows 10/older systems
- Added tool restriction to facing and grooving tools based on material diameter
- Auto comment option with filename content
- Implemention of online help that points to the fastseal.eu/blog

## [5.2.6.9] - 2022-06-15
- Hotfix on rought machining (XFinish null)
- AfterToolChangeCode added to machine settings.
- Fixed Pre/Post operations disappear when toggling coolant/vacuum.

## [5.2.6.8] - 2022-06-14
- Added R33
- Improved code output will less "air cutting"
- Default machine with correct geometry db column

## [5.2.6.7] - 2022-06-08
- Added more options for line numbering
- Inverted part off cutting direction, also implemented for chevron tools
- Oring tooling is not now dependable of exact radius of the tool itself, but depends on the X reach
- Added more filters to works and quotes (5, 15 days and 1 month). Usefull when a large number of works exist on the database, lowering the performance
- Added more control over the R28 profile

## [5.2.6.6] - 2022-06-02
- Inverted part off cutting direction

## [5.2.6.5] - 2022-06-02
- Incremental arc mode changed to X increment in radius rather than in diameter to suit Siemens 810D (should be the default ?)

## [5.2.6.4] - 2022-06-01
- All profiles with orings now use the default orings cross sections on the database. See https://www.fastseal.eu/blog/o-ring-cross-sections-and-standards/ for detailed information
- Improvements on the import/export CSV files, that now allow the use of values with ', as content

## [5.2.6.3] - 2022-05-30
- Added RS15PL/RL; RS38PL/RL; RS40PL/RL; RS41PL/RL; PS47PL/RL; PS48PL/RL; PS49PL/RL
- Fixed issue with renamed profiles. On work list/prints the original name was present

## [5.2.6.2] - 2022-05-24
- Added R32P, PS11RL, PS45PL/RL; PS46PL/RL, WH22B, MHEC03, R17M
- Corrected arc tangents in some profiles
- Added Haas-40THE configuration
- Improved profile database generation

## [5.2.6.1] - 2022-04-26
- Added PS11PL
- Corrected the lack of tolerances, introduced on last update

## [5.2.6.0] - 2022-04-20
- Added GR03R2, RS16G, ORS01
- Added button on comunication settings for manually send files with the objective of testing the configuration 

## [5.2.5.9] - 2022-04-11
- Improvements on TEM02, PS18E, PS20E, PS17E, R22A, R22B, R28A, R29A, R29B, R30A, SS13B, VPA01A, VPA01B
- Add the possibility to show imperial dimensions in decimals or fractions https://www.fastseal.eu/blog/dimensions-shown-in-metric-or-imperial/

## [5.2.5.8] - 2022-04-08
- Added EC04
- Limits changed on VPA01B

## [5.2.5.7] - 2022-04-06
- GR07 had wrong verification code for the capability of the outside grooving tool

## [5.2.5.6] - 2022-03-20
- ORC profile partoff code corrected
- Minor change on internal hardware detection
- Slava Ukraini

## [5.2.5.5] - 2022-03-20
- Added FPES12, GR03R
- Correction on WF03A and WF03B for larger sizes
- Minor change on PS18K
- Prevented some characters on clients names that resulted on invalid Windows folders

## [5.2.5.4] - 2022-03-09
- Added angles to FR02 and GR03
- CSV export fixed due to new column added
- Minor change on PS18K
- Emails changed
- Progressive change from Mastor brand to FastSeal own brand

## [5.2.5.3] - 2022-02-09
- Several profiles corrected and added more control on some of them
- Leadout with extra functionality to avoid the removal of the last element

## [5.2.5.2] - 2022-01-26
- Tool offset 11 graphics corrected on default seal
- Button added to a better user experience for updating the license
- Added work ID on the current work report

## [5.2.5.1] - 2022-01-19
- Latest update minor fix that affects RS06P.

## [5.2.5.0] - 2022-01-19
- Oring selection based on user database under test in profile RS06P.
- Relevant information added on the update window

## [5.2.4.9] - 2022-01-15
- Added pre and post instructions: https://www.fastseal.eu/blog/index.php/2022/01/14/pre-and-post-operations/

## [5.2.4.8] - 2022-01-12
- Improved rotary seal groove to take in consideration the tool dimension rather the old tool blade width setting (relates to update 5.2.4.6)
- Inicial release of the oring selection table (no functionality still present) - more information on https://www.fastseal.eu/blog/index.php/2021/11/18/o-ring-cross-sections-and-standards/

## [5.2.4.7] - 2022-01-07
- Fix on last update as GR01 and GR02 (possible others) were not deployed

## [5.2.4.6] - 2022-01-06
- Spring groove tool changed. Please check: https://www.fastseal.eu/blog/index.php/2022/01/06/spring-rotary-seal-groove-cutting-limits/
- Default seal machine have better description on the outside angle groove tools

## [5.2.4.5] - 2022-01-04
- Client menus improved
- Corrected several bugs related with new/clone/rename and delete of machines

## [5.2.4.4] - 2021-12-09
- Improvement on the database restore
- BUS03 inside front angle corrected (was fixed to 45 degrees)
- Grouped R15R/P into folder
- Added RS40P/R
- Corrected PS18O
- Improvement of the file template to ignore newlines as part of the filename

## [5.2.4.3] - 2021-12-03
- Improved lead-in/lead-out (0 size chamfer and zero angle cases fixed)
- Slower feedrate before finish pass in outside/inside cycles
- Added profiles: S21, HP, MHEC02, GR02A, SS29P/R, R17O, R17R, PS45, WH26, PS46P/R, PS48P/R, PS49P/R, PS06FT, RS06FT, RS38P/R
- Improvement on small cross section seals for PS06 and RS06
- Tool for restore database dump (beta)